 |
 |
Wiring Type:
B2, C2, D1 and E2 wiring types are standard and easily set
using a selector dial on the Logic 3.0 Control Board (L3). T and
TS wiring can be activated with use of a CPS-L or CPS-LN4.
Reversing Contactor Units (M) have C2 wiring standard and B2
available by simply moving a jumper wire. Operators are
pre-wired to accept a sensing edge, photoelectric sensors, radio
controls and most types of access control equipment. Failsafe
wiring can be selected with use of a CPS-L, CPS-LN4 or failsafe
edge and CPS3 card.
External Radio Control Terminal: Quick,
convenient connections for retrofitting or adding radio controls
on logic or mechanical operators.
Bearings: Ball bearings on output shaft;
heavy-duty, oil-filled bushings on reduction shafts.
Brake: Solenoid-actuated brake is standard on
3/4 and 1 HP units to prevent coasting of door. Optional on 1/3
and 1/2 HP units.
Friction Clutch: Adjustable, helps protect
against major damage to door and operator should the door meet
an obstruction.
Construction: NEMA 1 type electrical box,
heavy-duty 11-gauge steel frame with durable powdercoat finish,
all reduction sprockets drilled and pinned to shafts.
Push Button Station: 3-button station comes
standard and has open/close/stop functionality.
Quick-Mount Header Bracket: For fast,
swing-up mounting.
Rail Assembly: High-strength dual L-rail
track with nylon quiet-gliding chain guides on rail spacers for
quiet, smooth operation.
Control
Accessories
CPS® Commercial Protector System®:
(recommended) A “non-contact” photo safety sensor designed to
sense an obstruction and signal the door operator to reverse to
open.
Sensing Edge: (recommended) Designed to sense
an obstruction and signal door operator to stop or reverse as
desired. An electric or pneumatic sensing device can be added to
bottom edge of door.
Available Plug-in Options for Logic 3.0 (L3)
Auxiliary Contact: Used to operate security,
warning, heating or other 5V to 240V devices. Features both
normally open and closed contacts that actuate in conjunction
with limit switches.
Warning Signal: Red/green light module
provides safety warning prior to close (when using
timer-to-close feature). Also supports audio warning devices
and includes down mid-stop feature.
CPS3 Option: Enables the addition of a second
set of photo-eyes or 2- or 4-wire, self-monitoring edge.
|
|
|
» Printer Friendly Version
|
| |
|
|
|
Logic 3.0 Technology (L3)
Added Value
-
Built-in
3-channel, 315MHz radio receiver accepts up to
23 Security+® or unlimited DIP switch remotes.
3-button remotes can be programmed for
open/close/stop operation.
-
Maintenance Alert System™ establishes a routine
maintenance schedule based on the number of
cycles or calendar date. Includes
self-diagnostic system that allows you to
troubleshoot up to eight different error codes.
-
Timer-to-Close allows programming in 5-sec or
1-min increments. Commercial or industrial
photo-eyes required.
-
Thermal
motor overload can be easily reset from the
3-button floor level control station
Reliability &
Programming Simplicity
-
Switch less motor eliminates stuck start switch
and motor malfunctions on single-phase operators
-
All
high-voltage connections have been removed from
the board for safety and ease of service
-
Diagnostic LEDs speed installation and
troubleshooting
-
Motor
direction jumper lets you change motor direction
by simply moving a jumper
Mechanical Reversing Contactor Circuit (M):
(115V, 208/230V, 460V, 575V, 24V NEC Class 2 Circuit
with 40VA transformer) Industrial linear contactor
provides significantly longer control runs than
conventional contactors.
Standard Features
Motor:
Continuous-duty high-starting torque motor with instant
reverse and overload protection. Available in 1/3, 1/2,
3/4 and 1 HP; single- or three-phase. Removable without
affecting limit switch settings.
Drive Reduction: First-stage
heavy-duty 5L V-belt; second-stage #41 chain; output on
trolley #48 chain on 1/3 and 1/2 HP; #41 chain on 3/4
and 1 HP.
Emergency Disconnect: Spring-loaded
for emergency manual operation.
|
|
| |
T LOGIC VERSION 2 |
|
|
T LOGIC VERSION 1 |
|
|
T MECHANICAL |
|
|
T LINK |
|
|
T-LOGIC 3 |
|
|
T-Quick Start Guide for L3 |
|
|
T |
|
|
T LOGIC CONTROL VERSION 2 |
 |
|
|
|
